You will turn in ONE report. Answer all questions. Write in complete sentences.
NAME_____________________ SECTION_________________ DATE___________________
PERFORMANCE TASK # 3
You will turn in ONE report. Answer all questions. Write in complete sentences.
You must hand this activity today. This activity is worth 50 points.
Part I. Qualitative Relationships (15 pts) Today you will substitute a technological device (for your eyes)- a light probe and probe meter to measure the light going through various materials. Obtain a light probe, CBL, and light source. Connect the probe to the CBL according to your instructor’s directions. The Light source is shown below to the left. It provides a beam of light. The light probe is shown below to the top right. It receives light from the light source. The CBL is shown below to the bottom right. The CBL gives a measurement/reading of the light received through the light probe.
Obtain a light probe, CBL, and light source. Connect the probe to the CBL according to your instructor’s directions. Turn the light source on and shine it onto the probe. Align the light and the probe so that the light shines directly into the probe in a straight line. Hit the ON/HALT button and then the MODE button. Adjust the position of the probe so that the meter reading is close to 0.80. The meter reading is the intensity of the light beam.
DO NOT CHANGE the space between the light source and probe for the remaining activity, as it will influence the intensity of light hitting the probe and hence, the meter reading. It may be convenient to mark the probe and light source positions with masking tape. Record the initial meter reading.
meter reading
Block the light beam with your hand to verify that the CBL responds rapidly by dropping radically in value. If it does not, check with your instructor before proceeding.
Place a sunglass lens directly in front of the light source. What happens? Why?
meter reading
Is there any light going through the lens? How do you know? Add another lens, so that you have two in place. What happens? Why?
meter reading ________
Add a third lens and note what happens? meter reading __________
State a relationship between the amount of light absorbed by the lens material and thickness in words and as a mathematical equation.
As more light is absorbed, what happens to the amount of light transmitted (light that goes through the material)?
State a relationship between absorption and transmission in words and as a mathematical equation.
2. Place a bottle with only distilled water in it between the light source and the probe. What happens?
meter reading _________
Some light is absorbed by the distilled water.
0.62
Remove the distilled water bottle and place a bottle of green solution (a green solid dissolved in distilled water) between the light source and the probe. What happens? Why?
meter reading __________
If you were adjusting or standardizing a machine (to make sure the settings were all correct) before taking a light measurement through a colored solution, why might you begin by placing a sample of distilled water between the light and the probe?
Place a second bottle of green-colored solution in the light beam, in line with the first bottle. What happened? Why?
meter reading _________
State the relationship between pathlength, which is the distance light traveled through the solution, and the amount of light absorbed in words and mathematically.
Obtain the three bottles of blue solution of varying concentrations. See if you can line them up in order from least concentrated to most concentrated just by looking at them. Place them one at a time at the same spot between the light source and the probe.
Prediction: Most concentrated a) b) c)
Least concentrated a) b) c)
Actual readings (see the diagrams below): a)_____________ b)_____________
c)_____________
Was your estimation correct? How do you know if it was correct or incorrect?
0.29
0.68
Part II. Quantitative Relationships: Using a Spectrophotometer (30 pts)
The spectrophotometer is an electronic device that can take the place of your eye and the light source with probes and the light detector. A simplified diagram of what is inside the Spec-20 looks like this:
Io is the intensity of the light hitting the sample. An added feature of the spectrophotometer is that it can select a particular wavelength of light to shine on the sample. When we used the light probes, we were using white light which contains all the wavelengths in the visible spectrum. The spectrophotometer is an electronic device that can take the place of your eye and the light source with probes and the light detector. A simplified diagram of what is inside the Spec-20 looks like this:
Io is the intensity of the light hitting the sample. An added feature of the spectrophotometer is that it can select a particular wavelength of light to shine on the sample. When we used the light
probes, we were using white light which contains all the wavelengths in the visible spectrum.
I is the intensity of the light being transmitted through the sample, the amount of light that does not get absorbed by the sample. The amount of light absorbed by the sample will be different depending on the wavelength of light hitting the sample.
The spectrometer displays absorbance, which is -log I/Io. Absorbance is directly proportional to the concentration of the sample.
The samples are inserted into the machine through a covered slot on the top. The glass used to hold the sample is special optical glass (the light must go straight through the sample). It is important that these tubes be clean and free of fingerprints as any marks on the tube can block some of the light and change your results. There is lens paper available for cleaning the tubes.
Only hold the tubes near the top.
Overall Task: There are five tubes of a given solution with the concentration in moles/liter marked on the tubes. There are also three tubes of same solution of unknown concentration.
You must find the absorbances of the five known solutions.
Plot the absorbance versus concentration and generate the curve that describes the relationship.
Answer all questions relating to the data and graph.
Find the absorbances of the three unknown solutions from the resulting curve. (25 pts)
Since the absorbance will be different with different wavelength settings, you must first determine which wavelength gives the maximum absorbance. When this is determined, set the spectrometer to this wavelength for the rest of the task.
Before you start anything, locate nine sample tubes (in a rack) that contain: distilled water; 5 different concentrations of known solution; and, 3 solutions of unknown concentration (with code letters). You are now ready to begin by standardizing the spectrophotometer.
Standardizing and Using the Spectronic 20D
Below is a schematic diagram of the Spectronic 20D.
NOTES: *There are special sample tubes that must be used for the Spec 20. Be sure that any samples placed in the instrument are in these special test tubes.
*The sample chamber must be closed when making any measurement or adjustment.
*Be sure the power is on and that the instrument has had 15 minutes to warm up.
1. Set the wavelength for the measurement using the wavelength control knob on the top right of the instrument.
2. Be sure the mode is set to transmittance using the mode button.
3. With the sample chamber empty, turn the zero control (left knob on lower front) until the readout is 0% transmittance. This will correct for any stray light that may be in the chamber.
4. Change the mode to absorbance and place a tube with distilled water (or your blank) into the sample chamber. Adjust the absorbance control (right knob on lower front) until it reads 0 absorbance. This provides a control for absorbance due to the glass, water, or reagents.
5. Place your sample in the sample chamber, close the cover, and read the absorbance value from the digital readout.
6. If you are measuring the absorbance of more than one sample it is advisable to place the blank (may be distilled water) into the instrument and make any necessary adjustments between samples. If you change wavelengths, YOU MUST readjust the Spec 20 with the blank before making an absorbance reading.
Set the wavelength on 400 nm to begin the standardization for today’s activity.
Determining the Wavelength of Maximum Absorbance ( max )
1. Standardize the Spec-20 using the directions above. Select one of the solutions of known concentration (not the most dilute or most concentrated). Place it in the sample chamber and record the absorbance.
2. Remove the sample tube and change the wavelength to 420 nm. Repeat the standardization procedure. Place the same sample in the instrument and record the absorbance. Repeat this procedure changing the wavelength by 20 nm until you reach 600 nm.
Wavelength Absorbance
400 nm
0.173
420 nm
0.202
440 nm
0.282
460 nm
0.650
480 nm
0.920
500 nm
1.150
520 nm
1.230
540 nm
0.885
560 nm
0.458
580 nm
0.300
600 nm
0.066
The wavelength that produced the highest absorbance was nm.
3. Set the instrument to this maximum wavelength for the rest of the procedure.
Measuring Standard Solutions, and Solutions of Unknown Concentration
1. After setting the instrument to the wavelength that produced the highest absorbance, restandardize machine and collect absorbance data for the five known samples. (Even though you did one sample before it will be more accurate if you collect all data once you have set the wavelength to the maximum). Record distilled water as an additional sample. Consider it a data point. If you correctly standardized the Spec 20, the absorbance for distilled water will be 0.
Sample concentrations (known/given—called Standard Solutions)
Absorbance (determined by experiment)
0.000M (water/blank)
0.000
0.020M
0.150
0.050M
0.382
0.100M
0.634
0.150M
0.950
0.200M
1.230
2. Measure the absorbance reading for the three Unknown samples.
Sample concentrations Unknown find graphically, or mathematically (via regression equation)
Absorbance (determined by experiment)
Unknown F2
0.350
Unknown K6
0.585
Unknown B5
1.035
3. Next, you will plot a Standard Curve by graphing the absorbances (obtained at λmax) versus their corresponding standard concentrations (known solution concentrations). Before you plot the data, answer the following questions.
Which is the independent variable? (circle one): concentration absorbance Explain why.
Therefore, which variable should be plotted on the x-axis?
What type of mathematical relationship should you expect to see when you plot the data? Explain why.
Plot the data on the graph paper included below (print as many copies as you need).
Draw the calibration curve that best fits the data points. Make sure the curve goes through the origin (0,0). Be sure to include your graph with your submission.
Which type of relationship does the data show (circle one)? linear non-linear
4. Enter the data on the graphing calculator or using Excel and determine the regression equation and r2 value. If you use Excel, be sure that under Chart, Add Trendline, Options, you select the box “Set Intercept = 0″. Write the regression equation in terms of the lab variables and r2 below.
regression equation
r2
5. Determine the absorbance for each unknown along the curve by interpolation on the graph and from the regression equation.
Sample code for Unknown
Absorbance of Unknown
Concentration of Unknown from Graph
Concentration of Unknown from Regression Equation
F2
0.350
K6
0.585
B5
1.035
PART III (5 pts)
1. Summarize, in paragraph form, what you did, and what you found in both parts of this performance task.
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
LightProbe
000
Incident
lightbeam
Transmitted
light
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.41
Incident
lightbeam
Transmitted
light
Some light is absorbed bythe lens
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.22
Incident
lightbeam
Transmitted
light
Some light is absorbed bythe 2 lenses
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.12
Incident
lightbeam
Transmitted
light
Some light is absorbed bythe 3 lenses
Light Source 1 102
3
4 5 6
7 8
9
Light Transmittance Measurement
Light Probe
0.29
Incident light beam
Transmitted light
Some light is absorbed by the solution
a)
b)
c)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.29
Incident
light beam
Transmitted
light
Some light is absorbed by the solution
a)
b)
c)
Light Source 1 102
3
4 5 6
7 8
9
Light Transmittance Measurement
Light Probe
0.29
Incident light beam
Transmitted light
Some light is absorbed by the solution
a)
b)
c)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.29
Incident
light beam
Transmitted
light
Some light is absorbed by the solution
a)
b)
c)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
LightProbe
0.29
Incident
lightbeam
Transmitted
light
Some light is absorbed bythe solution
a)
b)
c)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.52
Incident
light beam
Transmitted
light
Some light is absorbed bythe solution
a)
b)
a)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.33
Incident
light beam
Transmitted
light
Some light is absorbed bythe solution
b)a)
a)
b)
c)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
Light Probe
0.68
Incident
light beam
Transmitted
light
Some light is absorbed bythe solution
a)
b)
c)
a)
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
LightProbe
0.44
Incident
lightbeam
Transmitted
light
Some light is absorbed bythe solution
a)
b)
c)
T
r
a
n
s
m
i
tt
a
n
c
e
A
b
s
o
r
b
a
n
c
e
C
o
n
c
en
tr
a
ti
o
n
1. Push the “Mode” button until the
red light lands on transmittance
2
.
T
u
r
n
t
h
i
s
k
n
o
b
u
n
t
i
l
t
h
e
d
i
g
i
t
a
l
r
e
a
d
o
u
t
i
s
~
0
.
0
0
0
0
.
0
0
0
T
r
a
n
s
m
i
tt
a
n
c
e
A
b
s
o
r
b
a
n
c
e
C
o
n
c
en
tr
a
ti
o
n
4
0
0
2
.
P
l
a
c
e
t
h
e
c
u
v
e
t
t
e
c
o
n
t
a
i
n
i
n
g
w
a
t
e
r
(
t
h
e
b
l
a
n
k
)
i
n
t
o
t
h
e
s
a
m
p
l
e
c
o
m
p
a
r
t
m
e
n
t
,
a
n
d
t
h
e
n
c
l
o
s
e
t
h
e
t
o
p
.
0
.
0
0
0
1. Push the “Mode” button until the
red light lands on absorbance
3
.
T
u
r
n
t
h
i
s
k
n
o
b
u
n
t
i
l
t
h
e
d
i
g
i
t
a
l
r
e
a
d
o
u
t
i
s
~
0
.
0
0
0
Sync the line on the cuvette withthe line on the sample holder.
T
r
a
n
s
m
i
tt
a
n
c
e
A
b
s
o
r
b
a
n
c
e
C
o
n
c
en
tr
a
ti
o
n
4
0
0
P
l
a
c
e
t
h
e
c
u
v
e
t
t
e
c
o
n
t
a
i
n
i
n
g
a
s
a
m
p
l
e
o
f
k
n
o
w
n
c
o
n
c
e
n
t
r
a
t
i
o
n
(
d
o
n
‘
t
u
s
e
t
h
e
m
o
s
t
o
r
t
h
e
l
e
a
s
t
c
o
n
c
e
n
t
r
a
t
e
d
s
a
m
p
l
e
)
i
n
t
o
t
h
e
s
a
m
p
l
e
c
o
m
p
a
r
t
m
e
n
t
,
a
n
d
t
h
e
n
c
l
o
s
e
t
h
e
t
o
p
.
0
.
0
0
2
Sync the lineonthe cuvettewith the line on thesampleholder.
Light
Source
1
10
2
3
4
5
6
7
8
9
Light Transmittance Measurement
LightProbe
0.80
Incident
lightbeam
Light traveling throughthe air.
Asmallamountisabsorbedbytheair.
Collepals.com Plagiarism Free Papers
Are you looking for custom essay writing service or even dissertation writing services? Just request for our write my paper service, and we'll match you with the best essay writer in your subject! With an exceptional team of professional academic experts in a wide range of subjects, we can guarantee you an unrivaled quality of custom-written papers.
Why Hire Collepals.com writers to do your paper?
Quality- We are experienced and have access to ample research materials.
We write plagiarism Free Content
Confidential- We never share or sell your personal information to third parties.
Support-Chat with us today! We are always waiting to answer all your questions.