January 20, 2023

Abstract (objectives)? A brief description of the experiment. The abstract should not exceed four or five sentences.? ?Introduction? In your own ?words, explain the reason for performing

Abstract (objectives)

A brief description of the experiment. The abstract should not exceed four or five sentences.

Introduction

In your own words, explain the reason for performing the experiment and give a concise summary of the theory involved, including any mathematical detail relevant to later discussion in the report.

Conclusions

This section should reflect your understanding of the experiment. Important points to include are a brief discussion of your final results, an interpretation of the actual experimental results as they apply to the objectives of the experiment set out in the introduction should be given. Also discuss any problems encountered and how they were resolved.

Electric Circuits Lab

Instructor: ———–

Analyses of Series and Parallel Resonant Filters

Student Name(s): Click or tap here to enter text.

Click or tap here to enter text.

Honor Pledge:

I pledge to support the Honor System of ECPI. I will refrain from any form of academic dishonesty or deception, such as cheating or plagiarism. I am aware that as a member of the academic community, it is my responsibility to turn in all suspected violators of the honor code. I understand that any failure on my part to support the Honor System will be turned over to a Judicial Review Board for determination. I will report to the Judicial Review Board hearing if summoned.

Date: 1/1/2018

Contents Abstract 3 Introduction 3 Procedures 3 Data Presentation & Analysis 4 Calculations 4 Required Screenshots 4 Conclusion 4 References 5

Abstract

(This instruction box is to be deleted before submission of the Lab report)

What is an Abstract?

This should include a brief description of all parts of the lab. The abstract should be complete in itself. It should summarize the entire lab; what you did, why you did it, the results, and your conclusion. Think of it as a summary to include all work done. It needs to be succinct yet detailed enough for a person to know what this report deals with in its entirety.

Objectives of Week 5 Lab 1:

· Build and test series resonant band-pass filters.

· Build and test parallel resonant band-stop filters.

· Calculate and measure the center frequency and bandwidth of series resonant band-pass filters

· Calculate and measure the minimum output voltage for parallel resonant band-stop filters.

· Use the Bode analyzer to observe and measure the frequency response of the filters.

Introduction

(This instruction box is to be deleted before submission of the Lab report)

What is an Introduction?

In your own words, explain the reason for performing the experiment and give a concise summary of the theory involved, including any mathematical detail relevant to later discussion in the report. State the objectives of the lab as well as the overall background of the relevant topic.

· This lab will review a series band-pass filter at various winding resistances to evaluate the effects of the inductors winding resistance on the center and critical frequencies, as well as bandwidth. After that we will review the output voltage of a parallel band-stop filter at different load resistances to prove that the purely resistive components after the LC parallel connection will not alter the frequency response but can alter the magnitude of the output voltage at the center frequency.

Procedures

Series Resonant Band-Pass Filter

Part I. Series Resonant Band-Pass Filter

1. Review the solution to Example 18-8 on pages 849-850 in your textbook.

2. Construct the circuit in Figure 1 in Multisim.

Figure 1. Series Resonant Band Pass Filter

3. Verify the following calculations for bandwidth from Example 18-8.

Calculate the resonant or center frequency, f0:

Calculate the inductive reactance, XL, at the center frequency f0:

Calculate the total circuit resistance:

Calculate the Q factor:

Finally, calculate the bandwidth, BW:

4. Measure the center frequency of the Series Resonant Band-Pass filter using the Bode plotter as shown in Figure 2.

Figure 2. Bode Plotter showing the Center or Resonant frequency

( Note: Connect the Bode Plotter as shown. Set the parameter as shown in the figure as well. Use Set… to set the resolution to 1000. Run the simulation. Use the cursor to find the maximum gain. This point of maximum gain is your center or resonant frequency (f0=107.4 kHz). Also note the gain at the center frequency (-0.828 dB). To find the bandwidth you will find the upper and lower critical frequencies where the gain is -3dB from the maximum. In this case we will record the frequencies where the gain is -0.828 dB – 3 dB = -3.828 dB.)

5. Measure the upper critical frequency as shown in Figure 3.

Figure 3. Upper critical frequency, f1=116.39 kHz

6. Measure the lower critical frequency as shown in Figure 4.

Figure 4. Lower critical frequency, f2 = 98.924 Hz

7. Subtract the lower critical frequency from the upper critical frequency to find the bandwidth.

8. Record your findings in Table 1. (The first row is completed for you.)

9. Repeat steps 2-8 using a winding resistance of Rw = 18 Ω

Table 1. Resonant Frequency and Bandwidth for Band-pass filter

Parallel Resonant Band-Stop Filter

Part II. Parallel Resonant Band-Stop Filter

1. Review the solution to Example 18-12 on pages 855-856 in your textbook.

2. Construct the circuit in Figure 5 below in Multisim.

Figure 5. Parallel Resonant Band-Pass Filter

3. Verify the following calculations for bandwidth and minimum output voltage for the example below. The center frequency is:

At the center or resonant frequency:

Use voltage-divider to find the minimum output voltage (magnitude only).

4. Measure the output gain in dB at the center or resonant frequency using the Bode Plotter as shown in Figure 6.

Figure 6. Gain at Resonant Frequency

5. Calculate the minimum output voltage from the definition of voltage gain in decibels (VdB).

6. Record your results in Table 2. The first row is completed for you.

Data Presentation & Analysis

RW	Calculated f0	Calculated BW	Measured f0	Upper Critical Frequency f1	Lower Critical Frequency f2	Measured BW f1-f2
10 Ω	107.3 kHz	17.5 kHz	107.4 kHz	116.39 kHz	98.824 kHz	17.47 kHz
18 Ω	107.3 kHz	18.76 kHz	107.399kHz	117.079kHz	98.342kHz	18.737kHz

Table 1: Calculated and measured values

RL	Calculated Center Frequency	Measured Center Frequency	Calculated Vout(min)	Measured Vout(min)
560 Ω	5.81 MHz	5.808 MHz	1.18 V	1.18 V
1.0 kΩ	5.81 MHz	5.808 MHz	1.92V	1.94 V

Table 2: Calculated and measured values

Calculations

Part 1 Step 3=

Part 2 Step 3=

Required Screenshots

Part 1 Series Resonant Band-Pass Filter

Figure 2. Bode Plotter showing the Center or Resonant frequency

Figure 3. Upper critical frequency

Figure 4. Lower critical frequency

Part 2 Parallel Resonant Band-Stop Filter

Figure 6 Gain at Resonant Frequency

Conclusion

(This instruction box is to be deleted before submission of the Lab report)

What is a Conclusion?

This section should reflect your understanding of the experiment conducted. Important points to include are a brief discussion of your results, and an interpretation of the actual experimental results as they apply to the objectives of the experiment set out in the introduction should be given. Also, discuss any problems encountered and how they were resolved.

Address the following in your conclusions:

· What did you notice about the cutoff frequencies for the low-pass and high-pass filters containing the same circuit elements?

· What voltage level does a gain of -3dB correspond to?

· What did you notice about the phase angle of the low-pass filters? Of the high-pass filters?

· Explain the above results in terms of circuit configurations (lead and lag circuits).

· How did changing the resistance change the cutoff frequency of the RL LPF? Of the RL HPF? Of the RC LPF? Of the RL HPF?

· How did changing the inductance change the cutoff frequency of the RL LPF? Of the RL HPF?

· How did changing the capacitance change the cutoff frequency of the RC LPF? Of the RC HPL?

References

(This instruction box is to be deleted before submission of the Lab report)

What is a Reference Section?

This section should list all sources used in the completion of the lab report using APA format. At a minimum, you should include your book and your instructor’s notes and videos. Be sure to list all sources to avoid plagiarism.

Note: The below reference section contains the reference for your book. Add to it as necessary. The second entry is the way to cite your instructor’s Zoom video.

Floyd, T. L., & Buchla, D. M. (2019). Principles of Electric Circuits (10th Edition). Pearson Education (US). https://bookshelf.vitalsource.com/books/9780134880068

National Instruments. (2019, April 3). Multisim Education Edition Version (14.2.0).

image3.png

image4.png

image5.png

image6.png

image7.png

image8.png

image9.png

image10.png

image11.png

image1.PNG

image2.png

image12.jpg

Electric Circuits Lab

Analyses of Series and Parallel Resonant Filters

I. Objectives:

After completing this lab experiment using, you should be able to:

1. Build and test series resonant band-pass filters.

2. Build and test parallel resonant band-stop filters.

3. Calculate and measure the center frequency and bandwidth of series resonant band-pass filters

4. Calculate and measure the minimum output voltage for parallel resonant band-stop filters.

5. Use the Bode analyzer to observe and measure the frequency response of the filters.

II. Parts List:

1. Resistor 8 Ω, 10 Ω, 18 Ω, 100 Ω, 560 Ω, 1 kΩ.

2. Inductor 5 µH, 1.0 mH.

3. Capacitor 2.2nF (0.0022 µF), 150 pF

4. Voltage Power Source 10 VRMS.

5. Bode Plotter

III. Procedures:

Series Resonant Band-Pass Filter

Part I. Series Resonant Band-Pass Filter

1. Review the solution to Example 18-8 on pages 849-850 in your textbook.

2. Construct the circuit in Figure 1 in Multisim.

Figure 1. Series Resonant Band Pass Filter

3. Verify the following calculations for bandwidth from Example 18-8.

Calculate the resonant or center frequency, f0:

Calculate the inductive reactance, XL, at the center frequency f0:

Calculate the total circuit resistance:

Calculate the Q factor:

Finally, calculate the bandwidth, BW:

4. Measure the center frequency of the Series Resonant Band-Pass filter using the Bode plotter as shown in Figure 2.

Figure 2. Bode Plotter showing the Center or Resonant frequency

5. Measure the upper critical frequency as shown in Figure 3.

Figure 3. Upper critical frequency, f1=116.39 kHz

6. Measure the lower critical frequency as shown in Figure 4.

Figure 4. Lower critical frequency, f2 = 98.924 Hz

7. Subtract the lower critical frequency from the upper critical frequency to find the bandwidth.

8. Record your findings in Table 1. (The first row is completed for you.)

9. Repeat steps 2-8 using a winding resistance of Rw = 18 Ω

RW	Calculated f0	Calculated BW	Measured f0	Upper Critical Frequency f1	Lower Critical Frequency f2	Measured BW f1-f2
10 Ω	107.3 kHz	17.5 kHz	107.4 kHz	116.39 kHz	98.824 kHz	17.47 kHz
18 Ω	107.3 kHz	18.76 kHz	107.399kHz	117.079kHz	98.342kHz	18.737kHz

Table 1. Resonant Frequency and Bandwidth for Band-pass filter

Parallel Resonant Band-Stop Filter

Part II. Parallel Resonant Band-Stop Filter

1. Review the solution to Example 18-12 on pages 855-856 in your textbook.

2. Construct the circuit in Figure 5 below in

Collepals.com Plagiarism Free Papers

Are you looking for custom essay writing service or even dissertation writing services? Just request for our write my paper service, and we'll match you with the best essay writer in your subject! With an exceptional team of professional academic experts in a wide range of subjects, we can guarantee you an unrivaled quality of custom-written papers.

Get ZERO PLAGIARISM, HUMAN WRITTEN ESSAYS

Why Hire Collepals.com writers to do your paper?

Quality- We are experienced and have access to ample research materials.

We write plagiarism Free Content

Confidential- We never share or sell your personal information to third parties.

Support-Chat with us today! We are always waiting to answer all your questions.

image3.png

image4.png

image5.png

image6.png

image7.png

image8.png

image9.png

image10.png

image11.png

image1.PNG

image2.png

image12.jpg

Related Posts