March 13, 2023

Identify which basic ?operational amplifier configuration is being used in the application ?(inverting, non-inverting or voltage divider) and which gain equation is ?needed for

Report on one of the topics from the list below and explain in your OWN words its basic operation, and uses. Identify which basic operational amplifier configuration is being used in the application (inverting, non-inverting or voltage divider) and which gain equation is needed for the application.

Comparators
Summing Amplifiers
Integrators
Differentiators

Electronic_Devices_10th_CH131.pptx

Electronic Devices

10th ed.

Chapter 13

Basic Op-Amp Circuits

Electronic Devices

10th ed.

◆ Describe and analyze the operation of several types of

comparator circuits

◆ Describe and analyze the operation of several types of

summing amplifiers

◆ Describe and analyze the operation of integrators and

differentiators

◆ Troubleshoot op-amp circuits

Objectives:

Electronic Devices

Comparators

A comparator is a specialized nonlinear op-amp circuit that compares two input voltages and produces an output state that indicates which one is greater. Comparators are designed to be fast and frequently have other capabilities to optimize the comparison function.

Electronic Devices

Comparators

An example of a comparator application is shown. The circuit detects a power failure in order to take an action to save data. As long as the comparator senses Vin, the output will be a dc level.

Electronic Devices

Comparator with Hysteresis

Sometimes the input signal to a comparator may vary due to noise superimposed on the input. The result can be an unstable output. To avoid this, hysteresis can be used.

Electronic Devices

Comparator with Hysteresis

Sometimes the input signal to a comparator may vary due to noise superimposed on the input. The result can be an unstable output. To avoid this, hysteresis can be used.

Hysteresis is incorporated by adding regenerative (positive) feedback, which creates two switching points: the upper trigger point (UTP) and the lower trigger point (LTP). After one trigger point is crossed, it becomes inactive and the other one becomes active.

Electronic Devices

Comparator with Hysteresis

A comparator with hysteresis is also called a Schmitt trigger. The trigger points are found by applying the voltage-divider rule:

and

Electronic Devices

Comparator with Hysteresis

A comparator with hysteresis is also called a Schmitt trigger. The trigger points are found by applying the voltage-divider rule:

and

Example:

What are the trigger points for the circuit if the maximum output is ±13 V?

Electronic Devices

Comparator with Hysteresis

A comparator with hysteresis is also called a Schmitt trigger. The trigger points are found by applying the voltage-divider rule:

and

Solution:

Example:

What are the trigger points for the circuit if the maximum output is ±13 V?

Electronic Devices

Comparator with Hysteresis

A comparator with hysteresis is also called a Schmitt trigger. The trigger points are found by applying the voltage-divider rule:

and

Solution:

Example:

What are the trigger points for the circuit if the maximum output is ±13 V?

= 2.28 V

Electronic Devices

Comparator with Hysteresis

A comparator with hysteresis is also called a Schmitt trigger. The trigger points are found by applying the voltage-divider rule:

and

Solution:

Example:

What are the trigger points for the circuit if the maximum output is ±13 V?

= 2.28 V

By symmetry, the lower trigger point = -2.28 V

Electronic Devices

Output Bounding

Some applications require a limit to the output of the comparator (such as a digital circuit). The output can be limited by using one or two zener diodes in the feedback circuit.

The circuit shown here is bounded as a positive value equal to the zener breakdown voltage.

Electronic Devices

Comparator Applications

A comparator with hysteresis can produce a pulse with a variable duty cycle. For the circuit shown, Vout(max) ranges from 0 V to +5 V because of the GND and VDD connections on the LM311.

Electronic Devices

Comparator Applications

A comparator with hysteresis can produce a pulse with a variable duty cycle. For the circuit shown, Vout(max) ranges from 0 V to +5 V because of the GND and VDD connections on the LM311.

The input is the red triangle wave (0 to 4 V). The duty cycle is varied with R2.

With R2 set to 100%, a 50% duty cycle is the result.

Electronic Devices

Comparator Applications

A comparator with hysteresis can produce a pulse with a variable duty cycle. For the circuit shown, Vout(max) ranges from 0 V to +5 V because of the GND and VDD connections on the LM311.

The input is the red triangle wave (0 to 4 V). The duty cycle is varied with R2.

With R2 set to 5%, a short pulse is the result.

Electronic Devices

Comparator Applications

Question:

What will happen when R2 is set to zero?

Electronic Devices

Comparator Applications

When R2 is set at 0%, the comparator has no hysteresis, and the output is positive when the input triangle is negative.

Question:

What will happen when R2 is set to zero?

Answer:

Electronic Devices

Comparator Applications

By changing the GND ref to -5 V, another useful circuit is formed. The input is a 4 Vp triangle wave (-4 V to +4 V). The output is a square wave that is delayed by an amount that depends on the setting of R2.

Electronic Devices

Comparator Applications

Question:

What are the upper and lower trigger points when R2 is set to maximum?

Electronic Devices

Comparator Applications

Question:

What are the upper and lower trigger points when R2 is set to maximum?

Answer:

Electronic Devices

Comparator Applications

Question:

What are the upper and lower trigger points when R2 is set to maximum?

Answer:

= +3.94 V

Electronic Devices

Comparator Applications

Question:

What are the upper and lower trigger points when R2 is set to maximum?

Answer:

= +3.94 V

By symmetry, VLTP = -3.94 V

Electronic Devices

Comparator Applications

Simultaneous or flash analog-to-digital converters use 2n-1 comparators to convert an analog input to a digital value for processing. Flash ADCs are a series of comparators, each with a slightly different reference voltage. The priority encoder produces an output equal to the highest value input.

Electronic Devices

Comparator Applications

In IC flash converters, the priority encoder usually includes a latch that holds the converter data constant for a period of time after the conversion.

Electronic Devices

Summing Amplifier

A summing amplifier has two or more inputs; normally all inputs have unity gain. The output is proportional to the negative of the algebraic sum of the inputs.

Electronic Devices

Summing Amplifier

A summing amplifier has two or more inputs; normally all inputs have unity gain. The output is proportional to the negative of the algebraic sum of the inputs.

Example:

What is VOUT if the input voltages are +5.0 V, -3.5 V and +4.2 V and all resistors = 10 kW?

10 kW

Electronic Devices

Summing Amplifier

A summing amplifier has two or more inputs; normally all inputs have unity gain. The output is proportional to the negative of the algebraic sum of the inputs.

VOUT = -(VIN1 + VIN2 + VIN3)

= -(+5.0 V – 3.5 V + 4.2 V)

Solution:

Example:

What is VOUT if the input voltages are +5.0 V, -3.5 V and +4.2 V and all resistors = 10 kW?

10 kW

Electronic Devices

Summing Amplifier

A summing amplifier has two or more inputs; normally all inputs have unity gain. The output is proportional to the negative of the algebraic sum of the inputs.

VOUT = -(VIN1 + VIN2 + VIN3)

= -(+5.0 V – 3.5 V + 4.2 V)

Solution:

Example:

What is VOUT if the input voltages are +5.0 V, -3.5 V and +4.2 V and all resistors = 10 kW?

= -5.7 V

10 kW

Electronic Devices

Averaging Amplifier

An averaging amplifier is basically a summing amplifier with the gain set to Rf /R = 1/n (n is the number of inputs). The output is the negative average of the inputs.

Electronic Devices

Averaging Amplifier

An averaging amplifier is basically a summing amplifier with the gain set to Rf /R = 1/n (n is the number of inputs). The output is the negative average of the inputs.

Example:

What is VOUT if the input voltages are +5.0 V, -3.5 V and +4.2 V? Assume R1 = R2 = R3 = 10 kW and Rf = 3.3 kW?

3.3 kW

Electronic Devices

Averaging Amplifier

An averaging amplifier is basically a summing amplifier with the gain set to Rf /R = 1/n (n is the number of inputs). The output is the negative average of the inputs.

VOUT = -⅓(VIN1 + VIN2 + VIN3)

= -⅓(+5.0 V – 3.5 V + 4.2 V)

Solution:

Example:

What is VOUT if the input voltages are +5.0 V, -3.5 V and +4.2 V? Assume R1 = R2 = R3 = 10 kW and Rf = 3.3 kW?

3.3 kW

Electronic Devices

Averaging Amplifier

An averaging amplifier is basically a summing amplifier with the gain set to Rf /R = 1/n (n is the number of inputs). The output is the negative average of the inputs.

VOUT = -⅓(VIN1 + VIN2 + VIN3)

= -⅓(+5.0 V – 3.5 V + 4.2 V)

Solution:

Example:

What is VOUT if the input voltages are +5.0 V, -3.5 V and +4.2 V? Assume R1 = R2 = R3 = 10 kW and Rf = 3.3 kW?

= -1.9 V

3.3 kW

Electronic Devices

Scaling Amplifier

A scaling adder has two or more inputs with each input having a different gain. The output represents the negative scaled sum of the inputs.

Electronic Devices

Scaling Amplifier

A scaling adder has two or more inputs with each input having a different gain. The output represents the negative scaled sum of the inputs.

Example:

Assume you need to sum the inputs from three microphones. The first two microphones require a gain of -2, but the third microphone requires a gain

of -3. What are the values of the

input R’s if Rf = 10 kW?

10 kW

Electronic Devices

Scaling Amplifier

A scaling adder has two or more inputs with each input having a different gain. The output represents the negative scaled sum of the inputs.

Solution:

Example:

Assume you need to sum the inputs from three microphones. The first two microphones require a gain of -2, but the third microphone requires a gain

of -3. What are the values of the

input R’s if Rf = 10 kW?

10 kW

Electronic Devices

Scaling Amplifier

A scaling adder has two or more inputs with each input having a different gain. The output represents the negative scaled sum of the inputs.

Solution:

Example:

Assume you need to sum the inputs from three microphones. The first two microphones require a gain of -2, but the third microphone requires a gain

of -3. What are the values of the

input R’s if Rf = 10 kW?

5.0 kW

10 kW

Electronic Devices

Scaling Amplifier

A scaling adder has two or more inputs with each input having a different gain. The output represents the negative scaled sum of the inputs.

Solution:

Example:

Assume you need to sum the inputs from three microphones. The first two microphones require a gain of -2, but the third microphone requires a gain

of -3. What are the values of the

input R’s if Rf = 10 kW?

5.0 kW

10 kW

Electronic Devices

Scaling Amplifier

A scaling adder has two or more inputs with each input having a different gain. The output represents the negative scaled sum of the inputs.

Solution:

Example:

Assume you need to sum the inputs from three microphones. The first two microphones require a gain of -2, but the third microphone requires a gain

of -3. What are the values of the

input R’s if Rf = 10 kW?

5.0 kW

10 kW

3.3 kW

Electronic Devices

Scaling Amplifier DAC

An application of a scaling adder is the D/A converter circuit shown here. The resistors are inversely proportional to the binary column weights. Because of the precision required of resistors, the method is useful only for small DACs.

Electronic Devices

R/2R Ladder DAC

A more widely used method for D/A conversion is the R/2R ladder. The gain for D3 is -1. Each successive input has a gain that is half of previous one. The output represents a weighted sum of all of the inputs (similar to the scaling adder).

Electronic Devices

R/2R Ladder DAC

An advantage of the R/2R ladder is that only two values of resistors are required to implement the circuit.

Electronic Devices

The Integrator

The ideal integrator is an inverting amplifier that has a capacitor in the feedback path. The output voltage is proportional to the negative integral (running sum) of the input voltage.

Ideal

Integrator

Electronic Devices

The Integrator

The ideal integrator is an inverting amplifier that has a capacitor in the feedback path. The output voltage is proportional to the negative integral (running sum) of the input voltage.

Op-amp integrating circuits must have extremely low dc offset and bias currents, because small errors are equivalent to a dc input. The ideal integrator tends to accumulate these errors, which moves the output toward saturation. The practical integrator overcomes these errors– the simplest method is to add a relatively large feedback resistor.

Ideal

Integrator

Practical

Integrator

Electronic Devices

The Integrator

If a constant level is the input, the current is constant. The capacitor charges from a constant current and produces a ramp. The slope of the output is given by the equation:

220 kW

10 kW

0.1mF

Electronic Devices

The Integrator

If a constant level is the input, the current is constant. The capacitor charges from a constant current and produces a ramp. The slope of the output is given by the equation:

220 kW

10 kW

0.1mF

Example:

Sketch the output wave:

Vin

Electronic Devices

The Integrator

If a constant level is the input, the current is constant. The capacitor charges from a constant current and produces a ramp. The slope of the output is given by the equation:

220 kW

10 kW

0.1mF

Solution:

Example:

Sketch the output wave:

Vin

Electronic Devices

The Integrator

If a constant level is the input, the current is constant. The capacitor charges from a constant current and produces a ramp. The slope of the output is given by the equation:

220 kW

10 kW

0.1mF

Solution:

Example:

Sketch the output wave:

Vin

Electronic Devices

The Integrator

If a constant level is the input, the current is constant. The capacitor charges from a constant current and produces a ramp. The slope of the output is given by the equation:

220 kW

Collepals.com Plagiarism Free Papers

Are you looking for custom essay writing service or even dissertation writing services? Just request for our write my paper service, and we'll match you with the best essay writer in your subject! With an exceptional team of professional academic experts in a wide range of subjects, we can guarantee you an unrivaled quality of custom-written papers.

Get ZERO PLAGIARISM, HUMAN WRITTEN ESSAYS

Why Hire Collepals.com writers to do your paper?

Quality- We are experienced and have access to ample research materials.

We write plagiarism Free Content

Confidential- We never share or sell your personal information to third parties.

Support-Chat with us today! We are always waiting to answer all your questions.

Identify which basic ?operational amplifier configuration is being used in the application ?(inverting, non-inverting or voltage divider) and which gain equation is ?needed for

Related Posts

Which of the following describes the light distribution of a fixture? A. Wall bracket B. Semirecessed C. Direct/indirect D. Pendant 2. Of the following fixture conf

Create a?Word document?that contains the information listed below for at least?three?credible, expert-authored, timely (recent) sources you could use for your Problem/Solution

Introduction Building on the Strategic Planning and Development assignment from Week 3, prepare a 10-slide Microsoft PowerPoint presentation, with narration, of your p